DECT 6005
Accessory handset for
DECT 6015 and DECT 6035 Series
DECT6005 OM.indd
i
20/8/07 1:49:18 PM
Compatible Bases
This handset is compatible with Uniden’s 1.8GHz DECT 6015
and DECT 6035 expandable phone series.
Installing the Accessory Handset
Checking the Package Contents
Make sure your package contains the following items. If any
items are missing or damaged, contact our Customer Service
Hotline. See inside the back cover page for contact information.
• Cordless Handset
• Charger
• Belt Clip
• Printed Material
• AC Adapter (model # AAD-600S: Input 240V AC, 50 Hz;
Output 9V DC, 210 mA)
• Rechargeable NiMH Battery Pack (model # BT-652: Capacity
650 mAh, 2.4V)
Installing the Battery
Follow the steps below to install the
rechargeable battery pack.
1. Using the finger indentation, press in on
the battery case cover and slide it down
to remove it.
2. Plug the battery connector into the
battery compartment jack. Be sure to
match the red and black wires to the
label near the jack.
3. Gently pull on the battery wires. If the
battery connector comes loose, try
connecting it again.
4. Replace the battery case cover and
slide it up until it clicks into place.
Note: Use only the Uniden BT-652
rechargeable battery pack supplied
with your cordless telephone.
2
DECT6005 OM.indd
2
20/8/07 1:49:20 PM
Installing the Belt Clip
Line up the tabs with the holes on each side of
the handset. Press the belt clip down until both
tabs click into place.
To remove the belt clip, pull both sides of the clip
to release the tabs from the holes.
Installing the Optional Headset
Your phone may be used with an optional
headset. To use a headset, insert the headset
plug into the headset jack. Headsets may
be purchased by calling the Uniden Parts
Department. See inside the back cover page for
contact information.
Charging the Accessory Handset
The handset is powered by a rechargeable battery pack that
automatically recharges when the handset is placed in the
charger.
1. Connect the AC adapter to the DC IN 9V jack and to a 240V
AC outlet that is not controlled by a wall switch.
Caution: Use only the Uniden AAD-600S adapter.
2. Set the charger on a
Route the cord.
desk or tabletop, and
place the handset in the
charger with the keypad
facing forward.
3. Make sure that the
charge LED illuminates.
To AC outlet
If the LED does not
To DC IN 9V
illuminate, check to see
that the AC adapter
is plugged in and
AC adapter (supplied)
the handset makes
Caution: Use only the Uniden AAD-600S adapter.
good contact with the
charging contacts on the charger.
4. Charge the handset battery pack for at least 15-20 hours
before using your new handset for the first time.
3
DECT6005 OM.indd
3
20/8/07 1:49:20 PM
Registering the Handset
You must register the handset to the base before you can use it.
Only one handset can be registered at a time. (If an accessory
handset has ever been registered to a base, you must reset the
handset before you can register it to a new base.)
To register to a DECT 6000
series base, place the
Charge the handset
for 15-20 hours.
Extra Handset
accessory handset in the base.
While the handset is registering,
HANDSET REGISTERING
appears in the LCD. When
REGISTRATION COMPLETE is
displayed, the handset has been
registered to the base.
If REGISTRATION FAILED
appears, pick up the handset
from the base and try again.
Charger
Extra Handset
Place the extra handset
in the main base to
register.
Main Base
Registration
Complete.
Base #1
Extra Handset
+
Main Base
Charger
Resetting the Handset
If you want to register the handset to a different base or replace
a handset with another one, you must first clear the registration
information from the base and the handset.
1. Press and hold [ ] and [#] for at least five seconds, until the
SYSTEM RESET menu appears.
2. Select the DEREGISTER HS
Which Handset?
submenu by pressing [Menu/Select].
Handset
Handset
#1
#2
WHICH HANDSET? appears in the
display.
3. Use [ ] or [ ] to select the handset ID to be de-registered
from the list, and then press [Menu/Select]. DEREGISTER
HS appears.
4. Press [ ] to move the cursor to YES, and then press
[Menu/Select]. You will hear a confirmation tone.
4
DECT6005 OM.indd
4
20/8/07 1:49:20 PM
Resetting the Handset Without the Base
If the original base this handset was registered to is not
available for some reason (for example, it is lost or somehow
incapacitated), you can still reset the handset and use it with
another base.
1. Press and hold [ ] and [#] for more than five seconds, until
the SYSTEM RESET menu appears.
2. Press [ ] to move the cursor to BASE UNAVAILABLE and
then press [Menu/Select]. WHICH BASE? appears.
3. Press [ ] to move the cursor to the base which you want
to de-register from, and then press [Menu/Select]. BASE
UNAVAILABLE appears.
4. Press [ ] to move the cursor to YES, and then press
[Menu/Select]. You hear a confirmation tone, and the
handset deletes its own link to the base without trying to
contact the base.
Now you are ready to register the handset to the new base.
5
DECT6005 OM.indd
5
20/8/07 1:49:21 PM
Using the Interface
Parts of the Handset
5
6
1
2
3
4
7
14
15
16
8
9
10
17
18
11
19
20
12
13
21
22
1. Headset jack cover
2. Belt clip hole
12. [ /tone] key
13. [Redial/Pause] key
*
3. Speakerphone speaker
and ringer
4. Handset battery
compartment
5. new message LED
6. Handset earpiece
7. LCD display
14. [Menu/Select] key
15. [ /Mute] key (messages/
mute)
16. [ ] key (caller ID/right)
17. [ ] key (end call)
18. [ ] key (down)
19. [#] key
8. [Clear/Int’com] key
20. [ ] key (speaker)
21. Handset microphone
22. Handset charging contacts
9.
10. [ /Flash] key (talk/flash)
11. [ ] key (phonebook/left)
[
] key (up)
6
DECT6005 OM.indd
6
20/8/07 1:49:21 PM
Reading the Display
The handset display uses icons to tell you the status of your
phone. The table below lists the icons and what they mean.
Icon
Status
Description
Standby/ The battery icon indicates the handset
Talk
battery status: full, medium, low, and empty.
The ringer off icon indicates that the ringer
is turned off.
Standby
:OFF
The mute icon appears while the handset
Talk
Talk
microphone is muted.
The speaker icon appears when the handset
speaker phone is in use.
The privacy icon appears when the Privacy
Mode is turned on.
Talk
The voice mail icon appears when you have
messages waiting in your voice mailbox.
Standby
The Standby Screen
When the phone is in standby, the handset display shows the
following items:
Ringer off icon
(when the ringer is off)
:OFF
Handset #1
New CID: 5
battery icon
Handset ID
Number of new Caller ID calls received
Using the Four-way Function Key
Your handset has a four-way
function key that allows you
to move the cursor or pointer
on the display and access the
Up
most commonly used features
View the
View the
Caller ID
at the touch of a button.
phonebook
Press the left side of the
Four-way
Function Key
key to open the phonebook.
Press the right side to open
the Caller ID list.
Down
To use this four-way key, place your thumb over the key on the
handset and move to the four positions to get the feel of how it
moves and operates.
7
DECT6005 OM.indd
7
20/8/07 1:49:21 PM
Using the Handset Menus
To open the menu, press [Menu/Select]. Highlight the option
you want by pressing the four-way function key. This will move
the cursor; the option currently highlighted has a triangle beside
it. Activate the highlighted option by pressing [Menu/Select].
To go back to the previous screen, press [left] on the four-way
function key. To exit the menu and return to standby, press [ ].
If you do not press a key within thirty seconds, the phone will
time out and exit the menu.
Entering Text from Your Handset
You can use the number keypad on your handset to enter text
by referring to the letters printed on each number key. When you
press the number key in a text entry field, the phone displays
the first letter printed on the number key. Press the number key
twice to display the second letter and three times to display the
third. Capital letters are displayed first, then lower case letters,
and then the number on the key.
If two letters in a row use the same number key, enter the first
letter, then use [right] on the four-way function key to move the
cursor to the next position to enter the second letter.
Number of times key is pressed
8
DECT6005 OM.indd
8
20/8/07 1:49:22 PM
For example, to enter the word "Movies":
1. Press [6] once to enter M.
2. Use [right] on the four-way function key to move the cursor
to the right.
3. Press [6] six times to enter o.
4. Press [8] six times to enter v.
5. Press [4] six times to enter i.
6. Press [3] five times to enter e.
7. Press [7] eight times to enter s.
8. Press [Menu/Select] to end your text entry.
If you make a mistake while entering a name, use [right] or [left]
on the four-way function key to move the cursor to the incorrect
character. Press [Clear/Int’com] to erase the wrong character,
and then enter the correct character. To delete all characters,
press and hold [Clear/Int’com].
Note: When you enter the text, you can also use [#] to move the
cursor to right and [*/tone] to move the cursor to left.
9
DECT6005 OM.indd
9
20/8/07 1:49:22 PM
Using Your Accessory Handset
Making and Receiving Calls
With the earpiece
With the speaker phone
1. Pick up the handset from 1. Pick up the handset from
the cradle.
2. Dial the number.
3. Press [ /Flash].
the cradle.
2. Dial the number.
3. Press [
1. Pick up the handset.
2. Press [ ].
Make a
call
].
1. Pick up the handset.
(If AutoTalk is on, the
phone answers when you
pick up the handset from
the cradle.)
2. Press [ /Flash].
(If Any Key Answer is on,
you can press any key on
the dial pad.)
Answer
a call
Hang up Press [ ] or return the handset to the cradle.
Adjusting the Volume
Choose from four ringer volume settings (off, low, medium,
Ringer
Volume
and high). With the phone in standby, use [
] to make
the ringer volume louder or [
] to make it softer or turn it
completely off.
Choose from six volume levels for the earpiece. While on
a call, press [ ] to make the earpiece volume louder or
] to make it softer.
Earpiece
Volume
[
Choose from six volume levels for the handset
Speaker
Volume
speakerphone. While on a speakerphone call, press
[
] to make the speaker volume louder or [
] to make
it softer.
10
DECT6005 OM.indd 10
20/8/07 1:49:22 PM
Using Caller ID and Call Waiting
If you subscribe to Caller ID, you can store up to thirty Caller
ID numbers in each handset. Caller ID records are stored from
newest to oldest. Once your Caller ID list is full and you receive
an incoming call, the oldest record will be automatically deleted
to make room for the new record.
To open the Caller ID list, press [ ]. The phone will show the
number of new Caller ID records and the total number of stored
records. From the screen, you have the following options:
Scroll through the
records
Press [
] to scroll through CID records.
CID records are stored chronologically from
newest to oldest.
Store a record in the
phonebook
1. Find the record you want to store and
press [Menu/Select].
2. Move the cursor to STORE INTO PB, and
press [Menu/Select].
Dial a record
Find the entry you want to dial and press
[ /Flash] or [
].
Delete a record
1. Find the entry you want to delete and press
[Menu/Select].
2. Move the cursor to DELETE ENTRY, and
press [Menu/Select].
Delete all records
Press [Menu/Select].
Exit the Caller ID list
Press [ ], or press [
] (the left key on the
four-way function key) if you are on a call.
Using Call Waiting
If you subscribe to call waiting, a tone sounds if a call comes in
when you are on the phone. If you subscribe to Caller ID on call
waiting, the Caller ID information of the waiting call appears on
the display. Press [ /Flash] on the handset to accept the waiting
call. After a short pause, you will hear the new caller. To return to
the original caller, press [ /Flash] on the handset again.
11
DECT6005 OM.indd 11
20/8/07 1:49:23 PM
Using the Phonebook
Your handset can store up to seventy names and numbers in
your phonebook. When all the phonebook entries are full, you
will hear a beep and MEMORY FULL appears. You cannot store
any additional names and numbers unless you delete some of
the existing ones.
Press [ ] to enter the phonebook. Once in the phonebook, you
have the following options:
Scroll through Press [
] to scroll through the phonebook
the entries
alphabetically.
Jump to
entries that
start with a
certain letter
Press the number key corresponding to the letter you
want to jump to.
1. Press [Menu/Select].
Store a new
entry
2. Move the cursor to CREATE NEW, and then press
[Menu/Select].
1. Find the entry you want to copy, and press
Copy one
entry to
another
handset
[Menu/Select].
2. Move the cursor to COPY, and press [Menu/Select].
3. Move the cursor to select the handset you want to
copy the entry to, and press [Menu/Select].
Copy all
entries to
another
handset at
once
1. Press [Menu/Select], and then select COPY ALL.
2. Move the cursor to select the handset you want to
copy the entries to, and press [Menu/Select].
3. Move the cursor to YES, and press [Menu/Select].
1. Find the entry you want to dial.
Dial an entry
2. Press [ /Flash] or [
].
1. Find the entry you want to delete, and press [Menu/
Delete an
entry
Select].
2. Move the cursor to DELETE, and press [Menu/Select].
1. Press [Menu/Select].
Delete all
entries
2. Move the cursor to DELETE ALL, and press [Menu/
Select].
Close the
phonebook
Press [ ], or press [
] again if you are on a call.
12
DECT6005 OM.indd 12
20/8/07 1:49:23 PM
Redialing a Number
To redial one of the last five numbers dialed on this handset,
press [Redial/Pause]. This opens the redial list. Use [ ] and
[
[
] to find the number you want to dial, and press [ /Flash] or
] in standby, or press [Menu/Select] during a call.
Muting the Ringer (One Call Only)
While the handset is ringing, press [ ] to mute the ringer for this
call. The phone will ring again on the next call. (The handset
must be off the cradle to mute the ringer.)
Muting the Microphone
To mute the microphone so the caller can't hear you, press
[
/Mute] during a call. MUTE ON and appear in the display.
Press [ /Mute] again to cancel muting.
Privacy Mode
To prevent other stations from interrupting a call, press
[Menu/Select]. Move the cursor to CALL PRIVACY, and then
press [Menu/Select]. PRIVACY MODE ON and P appear in the
display. Repeat the procedure to turn off privacy mode.
Adjusting the Audio Tone
If you aren't satisfied with your phone's audio quality, you can
adjust the Audio Tone of the earpiece. While on a call, press
[Menu/Select]. Move the cursor to select AUDIO TONE, and
then press [Menu/Select]. Move the cursor to select desired
audio tone options: HIGH TONE, NATURAL TONE, or LOW
TONE. (The default setting, Natural Tone, is recommended for
hearing aid users.) Press [Menu/Select] to confirm. After two
seconds, the displayed audio tone is set, and the display returns
to normal.
13
DECT6005 OM.indd 13
20/8/07 1:49:24 PM
Using Hold, Conference, Transfer and Intercom
Press [Clear/int’com]. If you leave a caller on
hold for more than five minutes, the call will be
Put a call on hold
disconnected. To return to the party on hold, press
[ /Flash] or [
].
To join a call already in progress, press [ /Flash]
Join a call already
in progress
or [
]. You can hang up normally; the other
station remains connected to the call.
Press [Clear/int’com]; the call is placed on hold.
Use [
] or [
] to select the station you want to
transfer the call to, and press [Menu/Select]. (To
page all stations at once, select ALL.) When the
other station answers, you can talk to the station;
the outside call remains on hold. If the other
station accepts the call, you will be disconnected.
Transfer a call
To cancel the transfer and return to the call,
Cancel a transfer
press [ /Flash] or [
].
To answer the transfer page and speak to the
transferring station, press [ /Flash] or [Clear/
int’com]. To accept the call and speak to the
caller, press [ /Flash] again.
Accept a
transferred call
With the phone in standby, press [Clear/int’com].
Make an intercom Use [
] or [
] to select the station you want
page
to talk with, and then press [Menu/Select]. (If you
select ALL, all other stations will be paged.)
Cancel a page
To cancel the intercom page, press [ ].
Press [ /Flash] or [Clear/int’com]. If AutoTalk is
on, the handset automatically answers the page
when you pick up it from the cradle.
Answer an
intercom page
14
DECT6005 OM.indd 14
20/8/07 1:49:24 PM
Accessing Voicemail
If your base doesn't have an answering system and you
subscribe to a voice mail service, you can program your handset
to automatically dial the access number.
1. Press [Menu/Select].
2. Move the cursor to HANDSET SETUP and press
[Menu/Select].
3. Move the cursor to EDIT VOICE MAIL and press [Menu/
Select].
4. Enter your access number (up to twenty digits). If you need
the phone to wait before sending the next digits, press
[Redial/Pause] to insert a two-second pause. For a longer
pause, press [Redial/Pause] multiple times. Each pause
counts as one digit.
5. Press [Menu/Select] when you are finished.
Once you program your access number, press [ /Mute] to dial
your voice mail service.
Accessing Your Answering System
If your base has an answering system, you can use your handset
to get your messages and change your answering system setup.
You have the following options:
Play
messages
Press [ /Mute]. The system announces the number of
new and old messages and plays the message.
Press [
] to go to the start of the current message.
] repeatedly to go back to a previous
Repeat a
message
Press [
message.
Skip a
message
Press [
] to go to the beginning of the next message.
Delete a
message
While a message is playing, press [ ].
The message is permanently deleted.
Exit and
hang up
Press [ ] to exit the system and return to standby.
15
DECT6005 OM.indd 15
20/8/07 1:49:25 PM
Screening Calls
If your base has an answering system, you can listen to callers
as they leave a message. Press [ /Mute] when the system is
answering to listen to the caller without answering the phone.
Maintenance
Battery Life
With average use, your battery talk time will be approximately
ten hours and standby time will be approximately seven days.
For optimum performance, be sure to return the handset to the
cradle after each call. If the handset is left off of the cradle, the
actual talk time duration will be reduced respective to the amount
of time the handset is off the cradle.
Note: Do not place the power cord where it creates a trip hazard
or where it could become chafed and create a fire or
electrical hazard.
Low Battery Alert
When the battery pack is very low, the display shows LOW
BATTERY and the empty battery icon. If the phone is in standby,
none of the keys will operate. If you are on a call, complete your
conversation as quickly as possible, and return the handset to
the cradle.
Battery Replacement and Handling
With normal usage, your battery should last about one year.
If the talk time becomes short even after the battery is recharged,
please replace the battery. You can purchase a replacement
battery by calling Uniden's Parts department. See inside the
back cover page for contact information.
Warning:
To avoid the risk of personal injury or property damage from fire or
electrical shock, use only the BT-652 battery pack.
16
DECT6005 OM.indd 16
20/8/07 1:49:25 PM
Caution:
- This equipment contains a rechargeable Nickel-Metal-Hydride battery.
- Do not remove the batteries to charge them.
- Never throw the battery in a fire or disassemble or heat it.
- Do not remove or damage the battery casing.
- Do not short-circuit the battery.
- Do not charge the battery used in this equipment in any charger other
than the one designed to charge this battery as specified in the owner's
manual. Using another charger may damage the battery or cause the
battery to explode.
- Rechargeable batteries must be recycled or disposed of properly.
Clean the Battery Contacts
To maintain a good charge, clean
the charging contacts on the
handset once a month. Dampen
a cloth with plain water. Gently
rub the damp cloth over the
charging contacts until all visible
dirt is removed.
Dry the contacts thoroughly
before returning the handset to
the cradle.
Caution:
Do not use any chemical products (alcohol, paint thinner, etc.), or
you may discolor the surface and damage the finish.
17
DECT6005 OM.indd 17
20/8/07 1:49:26 PM
ONE YEAR LIMITED WARRANTY
UNIDEN DECT 6005 CORDLESS PHONE
IMPORTANT : Evidence of original purchase is required for warranty service.
WARRANTOR : Uniden Australia Pty Limited A.B.N. 58 001 865 498
Uniden New Zealand Limited
Warranty only available in original country of purchase.
ELEMENT OF WARRANTY :
Uniden warrants to the original retail owner for the duration of this warranty,
its UNIDEN DECT 6005 CORDLESS PHONE (herein after referred to as the
Product), to be free from defects in materials and craftsmanship with only the
limitations or exclusions set out below.
WARRANTY DURATION:
This warranty to the original retail owner only, shall terminate and be of no further
effect ONE (1) year after the date of original retail sale. This warranty will be
deemed invalid if the Product is;
(A) Damaged or not maintained as reasonable and necessary,
(B) Modified, altered or used as part of any conversion kits, subassemblies, or any
configurations not sold by Uniden,
(C) Improperly installed,
(D) Repaired by someone other than an authorized Uniden Repair Agent for a
defect or malfunction covered by this warranty,
(E) Used in conjunction with any equipment or parts or as part of a system not
manufactured by Uniden, or
(F) Where the Serial Number label of the product has been removed or damaged
beyond recognition. Warranty only valid in the country of original retail/sale.
PARTS COVERED:
This warranty covers for one (1) year, the Product and included accessories.
STATEMENT OF REMEDY:
In the event that the Product does not conform to this warranty at any time while
this warranty is in effect, the warrantor at its discretion, will repair the defect
or replace the Product and return it to you without charge for parts or service.
This warranty does not provide for reimbursement or payment of incidental or
consequential damages.
This EXPRESS WARRANTY is in addition to and does not in any way affect
your rights under the TRADE PRACTICES ACT 1974 (Cth) (Australia) or the
CONSUMER GUARANTEES ACT (New Zealand).
PROCEDURE FOR OBTAINING PERFORMANCE OR WARRANTY:
In the event that the Product does not conform to this warranty, the Product should
be shipped or delivered, freight pre-paid, with evidence of original purchase (e.g. a
copy of the sales docket), to the warrantor at:
UNIDEN AUSTRALIA PTY LIMITED
SERVICE DIVISION
345 Princes Highway, Rockdale NSW 2216
Fx(02) 9599 3278
UNIDEN NEW ZEALAND LIMITED
SERVICE DIVISION
150 Harris Road, East Tamaki, Auckland
Fx(09) 274 4253
Customers in other States should ship or deliver the Product freight pre-paid to
their nearest Uniden Authorized Repair Centre
(Contact Uniden for the nearest Warranty Agent to you).
18
DECT6005 OM.indd 18
20/8/07 1:49:26 PM
© 2007
Uniden Australia Pty Limited
Uniden New Zealand Limited
Printed in China
UUZZ01652BZ(0)
DECT6005 OM.indd 19
20/8/07 1:49:26 PM
|