Tripp Lite Battery Charger BP12V81 User Manual

Owner's Manual Addendum  
BP12V81  
Battery Pack Connection  
This addendum deals solely with the procedure to connect a BP12V81 Battery Pack to an Inverter/Charger. Follow all safety warnings and instructions  
included separately with the Battery Pack and Inverter/Charger prior to attempting connection.  
Step 1  
Place the Battery Pack close enough to the Inverter/Charger so that the Battery  
Pack's cables can reach.  
Step 5  
Restore AC power to the Inverter/Charger. The BP12V81 Battery Pack(s) and  
Inverter/Charger are now connected and ready to be used for battery backup  
applications.  
Step 2  
Step 6  
Place the Inverter/Charger's operating mode switch in the "OFF" position. Make  
sure the Inverter/Charger is unplugged from and/or not receiving power from any  
AC source. Make sure the Inverter/Charger is disconnected from any DC power  
source.  
Configuration  
Switches  
B4 B3 B2 B1 A4 A3 A2 A1  
Step 3  
Remove the half-inch of insulation on each  
of the wire ends of the red battery connector  
that is included separately with the  
BP12V81 Battery Pack. Connect the red  
battery connector's wire ends to the  
Inverter/Charger's DC terminals. Connect  
the RED wire to the Inverter/Charger's  
POSITIVE (+) DC terminal. Connect the  
BLACK wire to the Inverter/Charger's  
NEGATIVE (-) DC terminal.  
Set the Inverter/Charger's Configuration DIP Switches to the following positions.  
Note: the diagram represents the RV750UL and similar Inverter/Chargers. Select  
Inverter/Charger models do not include the B4, B3, B2 and B1 DIP Switches; in  
these cases, simply make the A4, A3, A2 and A1 settings recommended below.  
Switch  
B4  
Position Configuration  
UP  
UP  
Low Charge Amps  
WARNING!  
B3  
Equalize Battery - Leave in up position  
(Refer to Owner's Manual)  
Failure to observe proper polarity dur-  
ing connection could damage and void  
the warranties of both the BP12V81  
Battery Pack and the Inverter/Charger.  
B2  
DOWN B1 in up position and B2 in down position—Limit charging  
of the battery pack to 66% of the full load rating of the unit  
B1  
A4  
UP  
Securely tighten the Inverter/Charger's DC terminals to prevent the red battery  
connector's wires from coming loose due to accidental stress or tension.  
UP  
A3 and A4 both in up position—Unit will switch to battery  
backup when AC input voltage drops below 105VAC  
A3  
A2  
A1  
UP  
Step 4  
DOWN Battery Charger Enabled  
UP Gel Cell (Sealed) Battery  
Take the Inverter/Charger's red battery  
connector (A) and connect it to the red  
battery connector located at the end of  
the longer of the two cables on the  
BP12V81 Battery Pack (B).* The two  
connectors can only be joined with one  
orientation and should snap into posi-  
tion when pressure is applied.  
WARRANTY REGISTRATION  
Tripp Lite product.You'll be automatically entered into a drawing for a chance  
to win a FREE Tripp Lite product!*  
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.  
* Note: There are two cables located on the Battery  
Pack: a long cable and a short cable. The long cable  
is for connecting to the Inverter/Charger (or to an  
additional Battery Pack in an optional daisy-chain  
connection, see below). The short cable is only used  
in an optional daisy-chain connection (see below);  
otherwise, the short cable will remain unconnected.  
Optional Daisy-Chain Connection (for longer runtime)  
THREE BP12V81 BATTERY PACKS DAISY CHAINED TOGETHER  
BP12V81 BATTERY PACK  
BP12V81 BATTERY PACK  
BP12V81 BATTERY PACK  
INVERTER/CHARGER  
30A  
30A  
30A  
30A  
30A  
30A  
30A  
30A  
30A  
A
A
B
B
For longer runtime, daisy-chain two or more BP12V81 Battery Packs together. Take  
the daisy-chain cable, the shorter cable (A), of the Battery Pack closest to the  
Inverter/Charger and connect it to the external battery connector cable, the longer  
cable (B), of the Battery Pack you want to add. Repeat the procedure for each  
additional Battery Pack you connect.  
1111 W. 35th Street  
Chicago, IL 60609  
(773) 869-1234  
Copyright © Tripp Lite, 2005. All rights reserved. The policy of Tripp Lite is one of continuous improvement. Specifications and instructions are subject to change without notice. This product designed and engineered in the USA.  
200504148 93-2452  
 

Timex Watch W 102 User Manual
Timex Watch W111 User Manual
TiVo DVR SDOC 00104 000 Rev A1 User Manual
Toshiba Flat Panel Television 20A44 User Manual
TRENDnet Digital Camera TRENDnet User Manual
Tripp Lite Switch B119 003 User Manual
Tunturi Home Gym E85S User Manual
ViewSonic Car Video System VX2235wm User Manual
Volvo Automobile V70 User Manual
Waterpik Technologies Plumbing Product FN 20012813 F AB User Manual