TP Link Network Card TL POE200 User Manual

User Guide  
TL-POE200  
Power over Ethernet Adapter Kit  
Rev:2.0.0  
 
7106503932  
FCC STATEMENT  
This equipment has been tested and found to comply with the  
limits for a Class B digital device, pursuant to part 15 of the FCC  
Rules. These limits are designed to provide reasonable  
protection against harmful interference in  
a
residential  
installation. This equipment generates, uses and can radiate  
radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to  
radio or television reception, which can be determined by turning  
the equipment off and on, the user is encouraged to try to  
correct the interference by one or more of the following  
measures:  
¾
¾
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and  
receiver.  
¾
¾
Connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected.  
Consult the dealer or an experienced radio/ TV technician  
for help.  
This device complies with part 15 of the FCC Rules. Operation is  
subject to the following two conditions:  
1) This device may not cause harmful interference.  
2) This device must accept any interference received,  
including interference that may cause undesired operation.  
 
Any changes or modifications not expressly approved by the  
party responsible for compliance could void the user’s authority  
to operate the equipment.  
CE Mark Warning  
This is a class B product. In a domestic environment, this  
product may cause radio interference, in which case the user  
may be required to take adequate measures.  
Продукт сертифіковано згідно с правилами системи УкрСЕПРО  
на відповідність вимогам нормативних документів та вимогам,  
що передбачені чинними законодавчими актами України.  
SAFETY NOTICES  
¾
Do not use this product near water, for example, in a wet  
basement or near a swimming pool.  
¾
Avoid using this product during an electrical storm. There  
may be a remote risk of electric shock from lightning.  
 
Package Contents  
The following items should be found in your package.  
¾
¾
¾
¾
¾
TL-POE200 Power over Ethernet Adapter Kit  
Ethernet (CAT5 UTP) Cable  
Female-to-Female Power Connector  
48V DC Power Adapter  
This User Guide  
Note:  
)
Make sure that the package contains the above items. If any of  
the listed items are damaged or missing, please contact your  
distributor.  
Chapter 1 Introduction  
1.1 Overview of the Product  
Thank you for choosing the TL-POE200 Power over Ethernet  
Adapter Kit comprised of the Injector and Splitter. The Injector  
sends power and data over the Ethernet cable to the Splitter.  
Then the Splitter separates the data and power back into two  
cables and delivers them to the remotely located access point or  
other network device that requires a 5/9/12-volt power input.  
PoE (Power over Ethernet) technology allows the existing  
Ethernet infrastructure to transmit electrical power, along with  
data, to remote IP endpoints over the Ethernet cables, which  
can greatly save the cost of the external power cables. Your  
network can benefit from PoE technology for it will ensure the  
normal working status of your network while keeping the existing  
Ethernet infrastructure secure.  
 
1
       
1.2 Features  
¾
¾
Complies with IEEE 802.3, IEEE 802.3u standards  
Transmits electrical power along with data in one single  
cable  
¾
¾
Supports optional 5V DC , 9V DC or 12V DC power supply  
Supports Plug-and-Play for the devices, without any  
configuration  
¾
Elegant appearance with space-saving miniature size  
Chapter 2 Identifying External Components  
2.1 PoE Injector  
POWER+DATA OUT: Connect to the PD or PoE Receiver  
Adapter with a CAT5 UTP cable.  
 
2
       
LAN IN: Connect to a  
network device (such as  
a Switch or Router) with  
CAT5 UTP cable.  
DC 48V: Connect to the  
provided power adapter  
which can supply steady  
power of 48V DC.  
PWR: Power LED, a steady green light indicates  
that the power adapter is working properly.  
2.2 PoE Splitter  
POWER+DATA IN:  
Connect to the PSE  
or PoE Injector with  
a CAT5 UTP cable.  
Power-mode  
switch:  
You can choose the DC  
output of 12V, 9V or 5V  
by turning the switch to  
the left or right.  
Please make sure that the output voltage is  
correct, a wrong voltage may destroy the device  
which you want to power up.  
 
3
   
DC OUT: Connect to the  
power port of the Ethernet  
device with the provided  
power cable to supply the  
power of 5V, 9V or 12V DC.  
LAN OUT: Connect to  
the Ethernet device  
with CAT5 UTP cable  
to transmit data.  
PWR: Power LED, a steady green light indicates  
that the PoE Injector can supply power.  
Note:  
)
TL-POE200 Power over Ethernet Kit is not compliant with IEEE  
802.3af standard. The TL-POE200A (PoE Injector) and  
TL-POE200B (PoE Splitter) can only be operated together.  
Pairing the devices with any other PoE adapter is dangerous.  
Chapter 3 Connecting the Power over Ethernet  
Adapter Kit  
This chapter gives instructions on how to connect the Power  
over Ethernet Adapter Kit. Once connected, the Kit will  
transmit data and power over the Ethernet network cable to your  
remotely located network device.  
To connect the Power over Ethernet Adapter Kit, please take the  
following steps.  
 
4
   
Step 1: Insert one end of a Cat 5 Ethernet RJ45 Cable into the  
LAN IN port of the PoE Injector, and connect the other  
end of the cable to your network Switch or PC.  
Note:  
)
Do not mistake the LAN IN port with the POWER+DATA OUT  
port. Plugging the Ethernet cable into the wrong Ethernet port  
may cause serious damage to your network devices.  
Step 2: Plug one end of the Power Adapter into the DC 48V  
port of the PoE Injector and the other end into your  
electrical outlet. The green PWR LED on the PoE  
Injector should light up.  
Step 3: Connect another Cat 5 Ethernet RJ45 Cable from the  
PoE Injector’s POWER+DATA OUT port to the  
POWER+DATA IN port of the Splitter.  
Step 4: Insert one end of the DC Power Cable that is provided  
into the DC OUT port of the Splitter, and the other end  
into the corresponding DC port of the Network Device.  
The PWR LED on the Splitter should light up.  
Step 5: Connect the provided Cat 5 Ethernet RJ45 Cable from  
the LAN OUT port of the Splitter to the RJ45 LAN port  
of the Network Device.  
Note:  
)
Please make sure that the output voltage is correct, as a wrong  
voltage may destroy the device.  
At this point, your Network Device should have power and data,  
and function normally as shown in the figure below.  
 
5
 
6
Appendix: Specifications  
Normal  
IEEE  
802.3,  
IEEE  
802.3u,  
Standards  
CSMA/CD, TCP/IP  
DC 5V, 9V or 12V  
Voltage Output  
Output Power  
12V/1A, 9V/1A, 5V/2A  
1 10/100Mbps Auto-Negotiation RJ45  
LAN port  
TL-POE200A 1 10/100Mbps Auto-Negotiation RJ45  
PoE port  
1 48VDC Power Input Port  
Ports  
1
10/100Mbps Auto-Negotiation RJ45  
LAN port  
TL-POE200B 1 10/100Mbps Auto-Negotiation RJ45  
PoE port  
1 12/9/5V DC Power Output Port  
Cabling Type  
LED  
RJ45 CAT5 UTP cable  
PWR  
Safety & Emissions  
FCC, CE  
Environmental and Physical  
Operating Temp  
Storage Temp  
0~40(32~104)  
-40~70(-40~158)  
10%~90% RH, Non-condensing  
5%~90% RH, Non-condensing  
80.8*54*24 mm  
Operating Humidity  
Storage Humidity  
Dimensions (W*D*H)  
 
7
   

Technicolor Thomson Stereo System CS700 User Manual
Tekkeon Battery Charger MP3300 User Manual
TERK Technologies TV Video Accessories Advantage User Manual
Tiffen Camera Accessories PILOT AA User Manual
Toastmaster Fryer TCGF1200 User Manual
Toshiba CRT Television 32DF46 User Manual
Toshiba Scale SL59 SERIES User Manual
Triax Stereo System UFO Marine Antenna User Manual
Troy Bilt Trimmer TB15CS User Manual
Weed Eater Automobile Parts HP22 User Manual